New CJ intake

I’m going to order one and see how it works back to back with the Mafia on the 557. From the other site.

https://scontent.fmel4-1.fna.fbcdn.net/v/t1.6435-9/s600x600/240666053_4629145400443020_8150650326578195421_n.jpg?_nc_cat=105&ccb=1-5&_nc_sid=b9115d&_nc_ohc=1onAqH3S4-QAX9_TYwy&_nc_ht=scontent.fmel4-1.fna&oh=2c0fd2faa17852c1e84360e6a8d4c44d&oe=614D4E80

https://scontent.fmel4-1.fna.fbcdn.net/v/t1.6435-9/s600x600/239611196_4629145503776343_3785822218972877795_n.jpg?_nc_cat=110&ccb=1-5&_nc_sid=b9115d&_nc_ohc=RE6WEVodwPAAX9Oed1N&_nc_ht=scontent.fmel4-1.fna&oh=cf3995fab0de1cf6a30aa101dde91030&oe=614CE3C1


https://scontent.fmel4-1.fna.fbcdn.net/v/t1.6435-9/p160x160/239485618_4632345343456359_7607284926689304872_n.jpg?_nc_cat=100&ccb=1-5&_nc_sid=dbeb18&_nc_ohc=jou7vuUtJsIAX9zGpBC&_nc_ht=scontent.fmel4-1.fna&oh=064d4a493775290ab03f69a60b5ecc87&oe=614EA028

738drvr wrote:I’m going to order one and see how it works back to back with the Mafia on the 557.  From the other site.

https://scontent.fmel4-1.fna.fbcdn.net/v/t1.6435-9/s600x600/240666053_4629145400443020_8150650326578195421_n.jpg?_nc_cat=105&ccb=1-5&_nc_sid=b9115d&_nc_ohc=1onAqH3S4-QAX9_TYwy&_nc_ht=scontent.fmel4-1.fna&oh=2c0fd2faa17852c1e84360e6a8d4c44d&oe=614D4E80

https://scontent.fmel4-1.fna.fbcdn.net/v/t1.6435-9/s600x600/239611196_4629145503776343_3785822218972877795_n.jpg?_nc_cat=110&ccb=1-5&_nc_sid=b9115d&_nc_ohc=RE6WEVodwPAAX9Oed1N&_nc_ht=scontent.fmel4-1.fna&oh=cf3995fab0de1cf6a30aa101dde91030&oe=614CE3C1


https://scontent.fmel4-1.fna.fbcdn.net/v/t1.6435-9/p160x160/239485618_4632345343456359_7607284926689304872_n.jpg?_nc_cat=100&ccb=1-5&_nc_sid=dbeb18&_nc_ohc=jou7vuUtJsIAX9zGpBC&_nc_ht=scontent.fmel4-1.fna&oh=064d4a493775290ab03f69a60b5ecc87&oe=614EA028

What company produces this intake manifold ...? Where to get one ...?

Randy, it’s made by Eliminator. I think it’s 795 and I was told yesterday that IF it is port matched it is slightly better than a TFS Mafia(which I currently run). I was also told that it is not recommended to replace the Mafia with the CJ-V. Out of the box it is better than a Victor but only slightly better than the Mafia. I think if you port match both 1.5-2.0” in the runner they are about even. The CJ-V “might” be 5hp better.

Mike at Eliminator told me that both the Mafia and the AirBoss were used in the development of the CJ-V. FYI. the info. in the paragraph above DID NOT come from Eliminator.

Interestingly, you probably won’t be able to get a Mafia intake from TrickFlow this year. The new CJ-Vs are currently being produced and available but are being snatched up fast.

You can purchase one from any Eliminator dealer.
Dealers are listed on the Eliminator website.

738drvr wrote:You can purchase one from any Eliminator dealer.
Dealers are listed on the Eliminator website.

A customer of mine is searching for a better CAST intake for his 480 inch "class" pulling truck engine.
He has a highly modified Victor, (front and rear shorter runners), on cast iron CJ heads now so, I was just wondering.

Sounds perfect for him.

I don't know if these are hard to get now like the Mafia and a Dominator flange Victor. I ran across one if anyone is in need.

Not Mine Disclaimer. If their stocked now that's good too.

https://www.facebook.com/commerce/listing/1601530843679426/?media_id=0&ref=share_attachment