[b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
+3
'65 T-BOLT
bruno
mikep
7 posters
Page 1 of 1
[b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
548ci
lightened Eliminator block 4.600 bore with bushed .904 lifter bores
Block no longer has motor mounts so you would need to use a plate. But who would use them for this kind of power anyways
C-460 heads by Charlie so you now what they are.
WW 1.80 rockers
BJ custom sheetmetal intake which was 20hp better than my Hogans
2 SV-1 1240 CFM carbs
New BME rods 6.665 2.100" big end
JE lightened pistons 16-1
Scat lightened billet crank
Comp 60mm roller cam
Isky Red zone lifters
Manton 7/16 taper push rods
PSI 1250 coated valve springs
Manley Ty valves
Danny Bee
Meziere Water pump
JW flex plate
Skinny Kid motor plate.
Make 1152hp @ 8100rpm and 820ftlbs @ 6500rpm on a conservative dyno.
Ran 8.35 @ 165mph in a 3200lb 10" tire car in 4200 ft of air with a glide.
It has 4 dyno pulls and 17 1/8 mile passes. Spare parts available as well!
$15K or trade for???????
lightened Eliminator block 4.600 bore with bushed .904 lifter bores
Block no longer has motor mounts so you would need to use a plate. But who would use them for this kind of power anyways
C-460 heads by Charlie so you now what they are.
WW 1.80 rockers
BJ custom sheetmetal intake which was 20hp better than my Hogans
2 SV-1 1240 CFM carbs
New BME rods 6.665 2.100" big end
JE lightened pistons 16-1
Scat lightened billet crank
Comp 60mm roller cam
Isky Red zone lifters
Manton 7/16 taper push rods
PSI 1250 coated valve springs
Manley Ty valves
Danny Bee
Meziere Water pump
JW flex plate
Skinny Kid motor plate.
Make 1152hp @ 8100rpm and 820ftlbs @ 6500rpm on a conservative dyno.
Ran 8.35 @ 165mph in a 3200lb 10" tire car in 4200 ft of air with a glide.
It has 4 dyno pulls and 17 1/8 mile passes. Spare parts available as well!
$15K or trade for???????
Last edited by mikep on October 27th 2011, 6:32 pm; edited 1 time in total
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
1- do you have a pic on how it sits in the car ?
2- do you have a single cast/ carb setup for this deal ?
3- what size cam and do you have an issue with springs ?
4- if any how much nos can it handle/ i do also understand the tuning window is small with the comp ?
5- why are you selling ?
2- do you have a single cast/ carb setup for this deal ?
3- what size cam and do you have an issue with springs ?
4- if any how much nos can it handle/ i do also understand the tuning window is small with the comp ?
5- why are you selling ?
_________________
coming soon x275 build .........
thanks to all my sponsors :
www.OakleyMotorsports.com
www.Induction-Solutions.com
www.bfevansraceparts.com
www.ultimateconverter.com
www.keithfulpmotorsports.com
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
Nick, I know what you are thinking!!!!
'65 T-BOLT- Posts : 1464
Join date : 2009-08-28
Age : 53
Location : Hagerstown,Maryland
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
no sponsors next year and want to get out and do something more family like. This is a selfish sport.bruno wrote:1- do you have a pic on how it sits in the car ? Will get a pic today, but if you the aug. Issue of fsc it is in there.
2- do you have a single cast/ carb setup for this deal ? No.
3- what size cam and do you have an issue with springs ? around .950 and since coated the springs I ran these springs last year and they are still 450 on the seat so it is not a spring eater.
4- if any how much nos can it handle/ i do also understand the tuning window is small with the comp ? I was going to spray it next year and was told it would handle 200 withthe current ring gap and 350 with a re gap
5- why are you selling ?
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
I am selling the car as well. 25.3 stock suspension deal.
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
I can't seem to log into photobucket so you can pm me your email and I can send you a pic.
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
Spares included!
Set of bme rods
Set of psi 1250 springs
Set of isky .904 ez roll lifters.
Set of bme rods
Set of psi 1250 springs
Set of isky .904 ez roll lifters.
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
This is a dirt cheap steal for someone. Mike is a standup guy as well. It will be what he says it will be. Wish I needed another engine!
Nevs- BBF CONTRIBUTOR
- Posts : 2724
Join date : 2009-02-07
Age : 70
Location : NW Iowa(Odebolt)
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
Everyone can always use a spare engine
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
Separate? I want one of those SV1 carbs.
738drvr- Posts : 600
Join date : 2010-02-15
Age : 59
Location : Middle Tennessee
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
mikep wrote:Everyone can always use a spare engine
still never received an email and you never answered my ? ...also do you have the headers to sell also ?
_________________
coming soon x275 build .........
thanks to all my sponsors :
www.OakleyMotorsports.com
www.Induction-Solutions.com
www.bfevansraceparts.com
www.ultimateconverter.com
www.keithfulpmotorsports.com
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
You never pm'd me your email! The headers would go with the engine. And which question were you referring to since I answered all of them I thought?
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
mikep wrote:You never pm'd me your email! The headers would go with the engine. And which question were you referring to since I answered all of them I thought?
4- if any how much nos can it handle/ i do also understand the tuning window is small with the comp ? I was going to spray it next year and was told it would handle 200 withthe current ring gap and 350 with a re gap
res0rli9- BBF CONTRIBUTOR
- Posts : 3352
Join date : 2008-12-02
Age : 74
Location : sarasota FL.
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
If you are referring to the question you posted, the answer is the second sentence which was posted by me. I'm so confused
mikep- Posts : 64
Join date : 2009-08-14
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
Make offer!
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
How about a new bike?
http://nashville.craigslist.org/mcd/2577401187.html
http://nashville.craigslist.org/mcd/2577401187.html
738drvr- Posts : 600
Join date : 2010-02-15
Age : 59
Location : Middle Tennessee
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
Well my wife is a nurse and I cannot even get on a ladder so a bike is out of the question lol.
I am willing to part it out if I could get people to commit to buying the parts.
I am willing to part it out if I could get people to commit to buying the parts.
mikep- Posts : 64
Join date : 2009-08-14
Re: [b]548ci sheetmetal intake and SV-1s SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/b]
I'm interested in the Isky lifters if you're not too awful proud of them, PM me about them please
crittersf1- Posts : 521
Join date : 2009-10-28
Similar topics
» Hogan Sheetmetal intake for "A" Heads SOLD
» C460 sheetmetal intake
» C460 sheetmetal intake
» Boss 429 sheetmetal tunnelram SOLD !!!
» BBF 8-71 blower, Bif Uggly injector, Intake, spacer SOLD SOLD SOLD THANKS
» C460 sheetmetal intake
» C460 sheetmetal intake
» Boss 429 sheetmetal tunnelram SOLD !!!
» BBF 8-71 blower, Bif Uggly injector, Intake, spacer SOLD SOLD SOLD THANKS
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum