Mark McDonald T/S at Columbus
+7
bbf-falcon
Nevs
Lem Evans
56Tbird
Doug Rahn
John Myrick
c.evans
11 posters
Page 1 of 1
Mark McDonald T/S at Columbus
c.evans September 24th 2011, 6:36 pm
Mark's driving Jack Austin's Mustang and is in the show with a 7.19 @ 184.6 mph. 60'= 1.05, 1/8th= 4.573. 
Charlie Evans
Charlie Evans
c.evans- BBF VENDOR SPONSOR
- Posts : 2260
Join date : 2008-12-03
John Myrick- BBF CONTRIBUTOR
- Posts : 1153
Join date : 2011-02-05
Age : 62
Location : Maryland
Doug Rahn- BBF CONTRIBUTOR
- Posts : 1680
Join date : 2009-08-07
Age : 73
Location : Springfield, GA -
Re: Mark McDonald T/S at Columbus
56Tbird September 24th 2011, 7:46 pm
Charlie ,are you guys spraying that car? Those are some crazy fast times! Very Impressive!!
56Tbird- BBF CONTRIBUTOR
- Posts : 5260
Join date : 2008-12-02
Age : 65
Location : Hawesville,Ky.
Re: Mark McDonald T/S at Columbus
Lem Evans September 24th 2011, 7:52 pm
spray56Tbird wrote:Charlie ,are you guys spraying that car? Those are some crazy fast times! Very Impressive!!
Lem Evans- Posts : 7445
Join date : 2008-12-03
Location : Livermore , Ky -
Re: Mark McDonald T/S at Columbus
56Tbird September 24th 2011, 8:03 pm
That's a Bad Azz ride..Spray or No Spray!!
56Tbird- BBF CONTRIBUTOR
- Posts : 5260
Join date : 2008-12-02
Age : 65
Location : Hawesville,Ky.
Re: Mark McDonald T/S at Columbus
c.evans September 24th 2011, 8:22 pm
New set of numbers guys, 7.134 @ 187.11 mph. The 1/8th numbers on that pass were 4.549 @ 156.39.
Yes Dan, this is the first weekend we've ever sprayed Jack's car. We've run 187 mph before "on motor", but we're spraying it down low in order to reduce the e.t. We never had the crankcase vacuum that we thought we should and Mark and I worked on it pretty hard this past week hunting for leaks. We found that each of the new Moroso sheet metal valve covers had three cracks in the welds (total of six) and then took them off and Mark rewelded them. We also did a couple of other things to it to help seal it up. Also this is the first time we have had some decent air to run it in.
Charlie
Yes Dan, this is the first weekend we've ever sprayed Jack's car. We've run 187 mph before "on motor", but we're spraying it down low in order to reduce the e.t. We never had the crankcase vacuum that we thought we should and Mark and I worked on it pretty hard this past week hunting for leaks. We found that each of the new Moroso sheet metal valve covers had three cracks in the welds (total of six) and then took them off and Mark rewelded them. We also did a couple of other things to it to help seal it up. Also this is the first time we have had some decent air to run it in.
Charlie
c.evans- BBF VENDOR SPONSOR
- Posts : 2260
Join date : 2008-12-03
Nevs- BBF CONTRIBUTOR
- Posts : 2724
Join date : 2009-02-07
Age : 70
Location : NW Iowa(Odebolt)
Re: Mark McDonald T/S at Columbus
bbf-falcon September 24th 2011, 9:48 pm
Now that my friend"is a FAST FORD"
bbf-falcon- Posts : 8995
Join date : 2008-12-03
Location : Jackson, Ohio
Re: Mark McDonald T/S at Columbus
cool40 September 25th 2011, 12:07 am
decent air is good! great job Charlie!c.evans wrote:New set of numbers guys, 7.134 @ 187.11 mph. The 1/8th numbers on that pass were 4.549 @ 156.39.
Yes Dan, this is the first weekend we've ever sprayed Jack's car. We've run 187 mph before "on motor", but we're spraying it down low in order to reduce the e.t. We never had the crankcase vacuum that we thought we should and Mark and I worked on it pretty hard this past week hunting for leaks. We found that each of the new Moroso sheet metal valve covers had three cracks in the welds (total of six) and then took them off and Mark rewelded them. We also did a couple of other things to it to help seal it up. Also this is the first time we have had some decent air to run it in.
Charlie
cool40- BBF CONTRIBUTOR
- Posts : 7313
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno
Re: Mark McDonald T/S at Columbus
rmcomprandy September 25th 2011, 11:03 am
c.evans wrote:New set of numbers guys, 7.134 @ 187.11 mph. The 1/8th numbers on that pass were 4.549 @ 156.39.
Yes Dan, this is the first weekend we've ever sprayed Jack's car. We've run 187 mph before "on motor", but we're spraying it down low in order to reduce the e.t. We never had the crankcase vacuum that we thought we should and Mark and I worked on it pretty hard this past week hunting for leaks. We found that each of the new Moroso sheet metal valve covers had three cracks in the welds (total of six) and then took them off and Mark rewelded them. We also did a couple of other things to it to help seal it up. Also this is the first time we have had some decent air to run it in.
Charlie
At least with some nitrous you guys have stopped trying to win with a knife at a gun fight.
rmcomprandy- Posts : 6157
Join date : 2008-12-02
Location : Roseville, Michigan -
DILLIGASDAVE- Posts : 2262
Join date : 2009-08-08
Location : Texas. pronounced "texASS"
Re: Mark McDonald T/S at Columbus
c.evans September 27th 2011, 11:20 am
Thanks guys, I'll pass the compliments on to Jack and Mark.
Charlie
Charlie
c.evans- BBF VENDOR SPONSOR
- Posts : 2260
Join date : 2008-12-03
Re: Mark McDonald T/S at Columbus
D. Sea September 27th 2011, 12:22 pm
Impressive!
Charlie, you gonna be at BG this weekend?
Charlie, you gonna be at BG this weekend?
D. Sea- Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky
Similar topics» Congrats Mark McDonald and Jack Austin
» Cleveland in a Maverick
» Mark L.
» Has Anyone Talked to Mark O'Neal Since He Sold Probe, Lately?
» YB Nationals live feed
» Cleveland in a Maverick
» Mark L.
» Has Anyone Talked to Mark O'Neal Since He Sold Probe, Lately?
» YB Nationals live feed
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum