Diamond piston clearance
2 posters
Page 1 of 1
Diamond piston clearance
Early inventory reduction sale:
-These prices are never coming around again. Don't miss out!
1 set: -30cc dish, +.030, Kaase reliefs, 1.35CH, 529 grams, SOLD
1 set: -28cc dish, +.040, OEM reliefs, 1.35CH, 546 grams, $699.00
2 sets: -7cc flat tops, +.040 and +.060, Dual OEM/Kaase releifs, 1.765CH, SOLD OUT
1 set: +10cc dome tops, +.080, OEM reliefs, 1.770CH, $650.00
-These prices are never coming around again. Don't miss out!
1 set: -30cc dish, +.030, Kaase reliefs, 1.35CH, 529 grams, SOLD
1 set: -28cc dish, +.040, OEM reliefs, 1.35CH, 546 grams, $699.00
2 sets: -7cc flat tops, +.040 and +.060, Dual OEM/Kaase releifs, 1.765CH, SOLD OUT
1 set: +10cc dome tops, +.080, OEM reliefs, 1.770CH, $650.00
Last edited by Carl on September 23rd 2009, 4:31 pm; edited 1 time in total
Carl- Posts : 284
Join date : 2008-12-03
Location : Colorado
Re: Diamond piston clearance
Flat tops are all gone.
Carl- Posts : 284
Join date : 2008-12-03
Location : Colorado
Re: Diamond piston clearance
Only two sets left.
Carl- Posts : 284
Join date : 2008-12-03
Location : Colorado
aa
Do the 28 cc dish pistons Have a 990 PIN ??
Not stealing the thread but I believe:
If you get a cast 4.5 crank and some eagle 6.7 rods you could make a 547 for cheap
Looks like 10.3 CR with 78cc heads .043 gasket and a 10.32 deck
Would make one hell of a street motor using Alum CJ heads (OEM Reliefs)
And if you had a 460 +30 motor with those heads just punch it .010 more add crank rods and pistons
Not stealing the thread but I believe:
If you get a cast 4.5 crank and some eagle 6.7 rods you could make a 547 for cheap
Looks like 10.3 CR with 78cc heads .043 gasket and a 10.32 deck
Would make one hell of a street motor using Alum CJ heads (OEM Reliefs)
And if you had a 460 +30 motor with those heads just punch it .010 more add crank rods and pistons
Rvesterby- Posts : 130
Join date : 2008-12-03
Location : Mo City Texas
Re: Diamond piston clearance
Rvesterby wrote:Do the 28 cc dish pistons Have a 990 PIN ??
Not stealing the thread but I believe:
If you get a cast 4.5 crank and some eagle 6.7 rods you could make a 547 for cheap
Looks like 10.3 CR with 78cc heads .043 gasket and a 10.32 deck
Would make one hell of a street motor using Alum CJ heads (OEM Reliefs)
And if you had a 460 +30 motor with those heads just punch it .010 more add crank rods and pistons
Yes, the -28cc dish pistons have a .990 pin. They'll work with a 4.500/6.700 combo or 4.300/6.800.
Carl- Posts : 284
Join date : 2008-12-03
Location : Colorado
Similar topics
» BBF Diamond piston
» DIAMOND PISTON CLEARANCE SALE
» needed diamond piston part number 40722 two of them
» Anyone know how close the Forged L2366f piston is to cast 429 piston?
» P51 466 piston
» DIAMOND PISTON CLEARANCE SALE
» needed diamond piston part number 40722 two of them
» Anyone know how close the Forged L2366f piston is to cast 429 piston?
» P51 466 piston
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum