BIG BLOCK FORD
Would you like to react to this message? Create an account in a few clicks or log in to continue.

466CI A429 Heads Roller Drag Car Combo

5 posters

Go down

466CI A429 Heads Roller Drag Car Combo Empty 466CI A429 Heads Roller Drag Car Combo

Post  D. Sea August 25th 2009, 1:52 pm

466CI

D1VE Block with Engine Systems 4-bolt splayed caps on 2,3 and 4 plus Main Studs on all 5 caps. Screw in core plugs.

Eagle BBC H-Beam rods connected to domed Custom BRC pistons 13:1 Compression Ratio

460 crank with 2.200" rod journals Internally balanced with SFI Dampner and Flywheel.

Aluminum A429 Heads with 2.245” Intake valves and 1.76” Exhaust valves. FRPP Roller Rockers and Jomar Stud Girdle. Comp Roller valve springs and Titanium Retainers.
Average Intake Flow of all 8 ports
0.100 (72) 0.200 (154) 0.300 (230) 0.400 (298) 0.500 (332) 0.600 (345) 0.700 (357) 0.750 (361)

Average Exhaust Flow of all 8 ports
0.100 (57) 0.200 (121) 0.300 (167) 0.400 (198) 0.500 (213) 0.600 (225) 0.700 (230) 0.750 (232)

Comp Cams Custom Roller
Duration @ .050 272° Intake and 280° Exhaust
Lobe separation 110°
Gross Valve lift .727 Intake and .727 Exhaust
Intake lobe degreed to 106° ATDC


Edelbrock Victor 4500 intake match ported to the heads and with port work in the flange area, topped with a custom 1100 cfm Pro-Systems Dominator and 1” HVH spacer

MSD Billet dizzy.
Jacobs Electronics Ignition box and Coil.
Taylor Plug Wires.

2" into 3.5" individual tube headers for Fox Chassis via D&D Automotive Specialists.

Fully rollerized C4 tranny built by JPT Transmissions with transbrake and reverse manual valve body. 8” Custom Drag Converter 4600-4800 stall.

Canton FOX pan with Canton Windage Tray.

Ford 9” Rear with full spool and 4.30:1 gears.
31” Hoosier Drag Slicks

Car weighs approx. 3100# including 180# driver.
D. Sea
D. Sea

Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  Old blue Racin Team August 28th 2009, 9:15 pm

What does it run, any ideas what kinda power it is making
Old blue Racin Team
Old blue Racin Team

Posts : 1579
Join date : 2009-07-03
Age : 34
Location : North Carolina

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  D. Sea August 31st 2009, 8:02 am

Old blue Racin Team wrote:What does it run, any ideas what kinda power it is making

This combination made 560hp on a Chassis Dyno with a C4 and 8" converter. At the track it ran 6.38 to 6.42 through the 1/8 and 10.00 to 10.05 through the 1/4 at 3200#
D. Sea
D. Sea

Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  Old blue Racin Team August 31st 2009, 8:26 am

Thats pretty good Very Happy
Old blue Racin Team
Old blue Racin Team

Posts : 1579
Join date : 2009-07-03
Age : 34
Location : North Carolina

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  D. Sea August 31st 2009, 11:41 am

Old blue Racin Team wrote:Thats pretty good Very Happy

When I put together the 534, it REALLY woke up these heads bom
D. Sea
D. Sea

Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  Old blue Racin Team August 31st 2009, 11:47 am

D. Sea wrote:
Old blue Racin Team wrote:Thats pretty good Very Happy

When I put together the 534, it REALLY woke up these heads bom

I imangine so Very Happy Very Happy
Old blue Racin Team
Old blue Racin Team

Posts : 1579
Join date : 2009-07-03
Age : 34
Location : North Carolina

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  RapidRuss September 17th 2009, 6:26 am

D. Sea wrote:
Old blue Racin Team wrote:What does it run, any ideas what kinda power it is making

This combination made 560hp on a Chassis Dyno with a C4 and 8" converter. At the track it ran 6.38 to 6.42 through the 1/8 and 10.00 to 10.05 through the 1/4 at 3200#

Damon, What was the rpm drop when you went to the 4.300" crank ? and did your use the same cam ? thats what about 650hp at the flywheel ?
RapidRuss
RapidRuss

Posts : 334
Join date : 2009-04-28
Age : 69
Location : Smith Mountain Lake , VA

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  D. Sea September 17th 2009, 11:55 am

Russ,

There was not RPM Drop as I could tell. The 534 likes to exceed 7K Twisted Evil

I WAS using the same cam and this year I swapped to an Albert Clark Bad Attitude Series camshaft and it picked up a little mph and a little ET based on similar weather conditions.
D. Sea
D. Sea

Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  RapidRuss September 17th 2009, 12:12 pm

D. Sea wrote:Russ,

There was not RPM Drop as I could tell. The 534 likes to exceed 7K Twisted Evil

I WAS using the same cam and this year I swapped to an Albert Clark Bad Attitude Series camshaft and it picked up a little mph and a little ET based on similar weather conditions.

Damn Damon, that sure is swingin that arm in there for sure !! sounds to me like the induction system and that cam are working very well together !! What kinda lift and dur..are you running for that think to breath so well up there Question r if you dont want to advertise it..you could PM oe email me .. Laughing
RapidRuss
RapidRuss

Posts : 334
Join date : 2009-04-28
Age : 69
Location : Smith Mountain Lake , VA

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  D. Sea September 17th 2009, 12:17 pm

Russ,

If I told you, then Albert would come for you Muahahahahaha............ Twisted Evil

276/286 and .785/.777

In time, I'm going to try a 1250 Quick Fuel, I think she will like it.
D. Sea
D. Sea

Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  RapidRuss September 17th 2009, 3:05 pm

D. Sea wrote:Russ,

If I told you, then Albert would come for you Muahahahahaha............ Twisted Evil

276/286 and .785/.777

In time, I'm going to try a 1250 Quick Fuel, I think she will like it.

Damn , thats a good size stick for 534"s.....No damn wonder it spins like a top... Giminie Christmas Cool
RapidRuss
RapidRuss

Posts : 334
Join date : 2009-04-28
Age : 69
Location : Smith Mountain Lake , VA

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  danger ranger March 26th 2010, 8:51 am

thats cool have you tried to pull a lower rpm run on the dyno like about 5500 and check to see where your peek torque and horse was? it seemed like my 557 did good with out of the box cj heads and a mild 675 roller and seemed to like the 7k rpm but when we turned it back to 5200 where it peaked torque at 680 it made better hp in the end it peaked 720 hp at 5600--680 tq at 5200

danger ranger

Posts : 16
Join date : 2009-09-13

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  Northwest outlaw March 26th 2010, 2:45 pm

Do you have a link or number for the Engine Systems 4-bolt splayed caps? Thanks Jason
Northwest outlaw
Northwest outlaw

Posts : 962
Join date : 2009-06-27
Age : 48
Location : Pinehurst Idaho

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  D. Sea March 26th 2010, 3:09 pm

This was a build from way back when and the block was already assembled with the 4 bolt caps when I got it. A guy near Bowling Green built the engine for a pulling truck with iron heads and then I swapped over to the aluminum heads.
D. Sea
D. Sea

Posts : 2768
Join date : 2008-12-02
Age : 55
Location : Kentucky

Back to top Go down

466CI A429 Heads Roller Drag Car Combo Empty Re: 466CI A429 Heads Roller Drag Car Combo

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum