Valve cover Gaskets
5 posters
Page 1 of 1
Valve cover Gaskets
t-bird racer August 16th 2015, 9:09 pm
I have used The SCE thick Cork/Laminate gaskets for several years. I went Onto SCE web site and noticed that they now offer a steel center over rubber type
gasket. Has anyone tried these compared to the Cork/Laminate?? Its for my N/A 521.
All opinions welcome
gasket. Has anyone tried these compared to the Cork/Laminate?? Its for my N/A 521.
All opinions welcome
t-bird racer- Posts : 193
Join date : 2010-01-10
Re: Valve cover Gaskets
cool40 August 16th 2015, 9:27 pm
Have you thought about cometic? Mine are around 3 years old and still work great. 
cool40- BBF CONTRIBUTOR
- Posts : 7313
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno
Re: Valve cover Gaskets
t-bird racer August 17th 2015, 9:06 am
Honestly,
I was not aware that they even were available for BBF. Looking up their catalog for part number now.
I was not aware that they even were available for BBF. Looking up their catalog for part number now.
t-bird racer- Posts : 193
Join date : 2010-01-10
Re: Valve cover Gaskets
cool40 August 17th 2015, 9:16 am
I got mine from Lem a few years ago. I check valve lash religiously and they keep on working.
cool40- BBF CONTRIBUTOR
- Posts : 7313
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno
Re: Valve cover Gaskets
bbf-falcon August 17th 2015, 12:45 pm
cool40 wrote:Have you thought about cometic? Mine are around 3 years old and still work great.
Lem drop shipped me a set last week. They are the shitts.
bbf-falcon- Posts : 8995
Join date : 2008-12-03
Location : Jackson, Ohio
Re: Valve cover Gaskets
t-bird racer September 9th 2015, 9:31 am
Anyone have the Part number for the race application
t-bird racer- Posts : 193
Join date : 2010-01-10
Re: Valve cover Gaskets
Lem Evans September 9th 2015, 10:13 am
C5205-125 is what is in the Cometic catalog.
C5205-188 is what I stock.......thicker...3/16" vs 1/8".
C5205-188 is what I stock.......thicker...3/16" vs 1/8".
Last edited by Lem Evans on September 28th 2015, 11:39 am; edited 1 time in total
Lem Evans- Posts : 7445
Join date : 2008-12-03
Location : Livermore , Ky -
t-bird racer- Posts : 193
Join date : 2010-01-10
Re: Valve cover Gaskets
t-bird racer October 2nd 2015, 10:13 pm
Received my gaskets today Lem! Thanks!!
t-bird racer- Posts : 193
Join date : 2010-01-10
Re: Valve cover Gaskets
t-bird racer October 2nd 2015, 10:53 pm
So here's is a question? Do these need any prep? Spray on high Tach or do they just go on dry????
t-bird racer- Posts : 193
Join date : 2010-01-10
cool40- BBF CONTRIBUTOR
- Posts : 7313
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno
Lem Evans- Posts : 7445
Join date : 2008-12-03
Location : Livermore , Ky -
Re: Valve cover Gaskets
Lem Evans October 3rd 2015, 11:54 am
I guess I should have said.....you could glue them on but, it is not required.
Lem Evans- Posts : 7445
Join date : 2008-12-03
Location : Livermore , Ky -
noslo533- Posts : 28
Join date : 2015-04-20
Similar topics» Trying out some edelbrock valve cover gaskets
» valve cover gaskets
» valve cover gaskets ......
» valve cover gaskets
» valve cover gaskets
» valve cover gaskets
» valve cover gaskets ......
» valve cover gaskets
» valve cover gaskets
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum