D.O.V.E. vale lengths
+2
c.evans
72mav
6 posters
Page 1 of 1
D.O.V.E. vale lengths
Whats the length on a set of stockers?
Thanks.
Al
Thanks.
Al
72mav- Posts : 1081
Join date : 2008-12-03
Age : 61
Location : central Michigan
Re: D.O.V.E. vale lengths
Al,
On the early heads they should be 5.265" on the intakes and 5.060" on the exhausts. Most manufacturers will have something close to that, such as 5.250" or so.
Charlie
On the early heads they should be 5.265" on the intakes and 5.060" on the exhausts. Most manufacturers will have something close to that, such as 5.250" or so.
Charlie
c.evans- BBF VENDOR SPONSOR
- Posts : 2260
Join date : 2008-12-03
Re: D.O.V.E. vale lengths
Thank You Uncle Charlie,
Looking for something .100 over for the roller going in it. Wasnt sure what the stock size was.
Thanks.
Al
Looking for something .100 over for the roller going in it. Wasnt sure what the stock size was.
Thanks.
Al
72mav- Posts : 1081
Join date : 2008-12-03
Age : 61
Location : central Michigan
Re: D.O.V.E. vale lengths
Remind me again,,,,,which heads?
Anyway, Lem has some 2.250" X 5.365" intake valves and 1.760" X 5.160" exhaust valves, (that have the beautifully shaped tulip backside) in stock, I think. These are like the FRPP Ford valves that are made in Argentina and they are certainly of a fine quality.
In regards to the SI Valves, they have several different grades, or "quality" of valves and you have to pay attention to which ones you're ordering. Their low-end stuff is not suitable for racing. Their premium valve is the Silverline series that Dave mentioned.
Charlie
Anyway, Lem has some 2.250" X 5.365" intake valves and 1.760" X 5.160" exhaust valves, (that have the beautifully shaped tulip backside) in stock, I think. These are like the FRPP Ford valves that are made in Argentina and they are certainly of a fine quality.
In regards to the SI Valves, they have several different grades, or "quality" of valves and you have to pay attention to which ones you're ordering. Their low-end stuff is not suitable for racing. Their premium valve is the Silverline series that Dave mentioned.
Charlie
c.evans- BBF VENDOR SPONSOR
- Posts : 2260
Join date : 2008-12-03
Re: D.O.V.E. vale lengths
On the valves Charlie mentioned you can get 2.000 installed Height no problem. They don't mess up the geometry either.
dfree383- BBF CONTRIBUTOR
- Posts : 14851
Join date : 2009-07-09
Location : Home Wif Da Wife.....
Re: D.O.V.E. vale lengths
WHAT GEOMETRY. I DOESN'T SEE NO GEOMETRY IN VALVE LENGHTS. GEOMETRY TAKE MORES THAN ONE PLANES.
GomerPyle- Posts : 5
Join date : 2010-03-22
Re: D.O.V.E. vale lengths
BY THE WAYS, WHATS IS CORPERATE INVERVENTION AND PROFIT? IT SEEMS TO ME LIKE YOU HAVES TO MUCH TIME ON YOU'RE HANDS. GETS TO THE POINT.
GomerPyle- Posts : 5
Join date : 2010-03-22
Re: D.O.V.E. vale lengths
WTFS IS POWER TO THE PEOPLE? ARE'S YOU THE PEOPLE?
GomerPyle- Posts : 5
Join date : 2010-03-22
Re: D.O.V.E. vale lengths
i DOESN'T THINK YOU'RE LOCATION IS NEAR ME. ARE YOU AN COMMUNIST? i THINKS SO.
GomerPyle- Posts : 5
Join date : 2010-03-22
Re: D.O.V.E. vale lengths
YOU DESUDS ME. YOU'RE NO AMERICAN GO BACK TO THE COUTRY YOUS CAME FROM!!!
GomerPyle- Posts : 5
Join date : 2010-03-22
Re: D.O.V.E. vale lengths
he's back
res0rli9- BBF CONTRIBUTOR
- Posts : 3352
Join date : 2008-12-02
Age : 74
Location : sarasota FL.
Re: D.O.V.E. vale lengths
Well gooooooollllleeeey.... Thier commies amoungst us....
dfree383- BBF CONTRIBUTOR
- Posts : 14851
Join date : 2009-07-09
Location : Home Wif Da Wife.....
Re: D.O.V.E. vale lengths
Get off my thread you goof-ball!!
Charlie,
Those were D.O.V.E. heads btw.
Regards.
Al
Charlie,
Those were D.O.V.E. heads btw.
Regards.
Al
72mav- Posts : 1081
Join date : 2008-12-03
Age : 61
Location : central Michigan
Re: D.O.V.E. vale lengths
res0rli9 wrote:he's back
I guess I missed it, who is this guy?
DILLIGASDAVE- Posts : 2262
Join date : 2009-08-08
Location : Texas. pronounced "texASS"
Similar topics
» P-51 Pushrod lengths
» valve lengths
» pushrod lengths
» trying to get pushrod lengths!!!!
» Shorty Glide lengths
» valve lengths
» pushrod lengths
» trying to get pushrod lengths!!!!
» Shorty Glide lengths
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum