BIG BLOCK FORD
Would you like to react to this message? Create an account in a few clicks or log in to continue.
BIG BLOCK FORD

BIG BLOCK FORD TECHNICAL AND PARTS SITE

OAKLEY MOTORSPORTS ENGINES, CUSTOM CARBS, COMPLETE ENGINE MACHINING, PORTING SERVICE AND DYNO SERVICE. CALL 270-344-0912, 270-929-5185


FS: Freshly CNC machined D1VE block, 4.420"

3 posters

BIG BLOCK FORD :: GENERAL TECH :: STUFF FOR SALE - B.F. EVANS RACE PARTS

Go down

FS: Freshly CNC machined D1VE block, 4.420" Empty FS: Freshly CNC machined D1VE block, 4.420"

Post  blykins October 26th 2010, 10:16 am

I have for sale a fresh block, CNC machined by Keith Craft Racing. It has been bored and will be honed with torque plates before shipment. Has also been align honed, square decked, painted gloss black (with glyptal in the lifter valley and timing cover area), cam bearings installed, freeze plugs installed, etc. It has new ARP main studs installed.

You will receive a block that is fully machined, ready to start assembling.

$850 + shipping.

blykins

Posts : 17
Join date : 2010-10-25
Location : Louisville, KY

http://www.b2motorsportsllc.com

Back to top Go down

FS: Freshly CNC machined D1VE block, 4.420" Empty Re: FS: Freshly CNC machined D1VE block, 4.420"

Post  poweredbyford October 26th 2010, 10:39 am

Where is it located at? thanks,Kevan

poweredbyford

Posts : 48
Join date : 2010-01-22

Back to top Go down

FS: Freshly CNC machined D1VE block, 4.420" Empty Re: FS: Freshly CNC machined D1VE block, 4.420"

Post  blykins October 26th 2010, 11:06 am

I'm near Louisville, KY.


blykins

Posts : 17
Join date : 2010-10-25
Location : Louisville, KY

http://www.b2motorsportsllc.com

Back to top Go down

FS: Freshly CNC machined D1VE block, 4.420" Empty Re: FS: Freshly CNC machined D1VE block, 4.420"

Post  jones October 26th 2010, 12:16 pm

2 or 4 bolt mains?
deck height?
bushed lifter bores?

jones

Posts : 2230
Join date : 2008-12-02
Location : Philadelphia, MS.

Back to top Go down

FS: Freshly CNC machined D1VE block, 4.420" Empty Re: FS: Freshly CNC machined D1VE block, 4.420"

Post  blykins October 26th 2010, 12:20 pm

As stated in subject line, D1VE block, 4.420" bore.

2 bolt mains...

Lifter bores have not been bushed.

Deck height is 10.300".

blykins

Posts : 17
Join date : 2010-10-25
Location : Louisville, KY

http://www.b2motorsportsllc.com

Back to top Go down

FS: Freshly CNC machined D1VE block, 4.420" Empty Re: FS: Freshly CNC machined D1VE block, 4.420"

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

BIG BLOCK FORD :: GENERAL TECH :: STUFF FOR SALE - B.F. EVANS RACE PARTS

 
Permissions in this forum:
You cannot reply to topics in this forum